RU

THZ5B-BL-DA-D0

P/N 202292

THz detector for power measurements up to 25 µW.

THZ5B-BL-DA-D0

Traceable calibration:

Logo nist

Ключевые особенности семейства продуктов

Relative Measurements from 0.1 to 30 THz

Broadband, room temperature operation, easier to use and less expensive than a Golay cell

Wide Dynamic Range from nW to mW

With state of the art pyroelectric sensors, measure down to 50 nW with 1 nW resolution.

Several Sensor Sizes Available

Choice of 5 mm and 9 mm diameter

Calibrated at 0.63 µm

THZ-B detectors are calibrated at a single wavelength (0.63 µm) and include typical wavelength correction data from 0.25 to 440 µm. They are used for relative measurements outside that range.

SDC-500 Optical Chopper

All THZ-B detectors require the use of an optical chopper, like our SDC-500, to sync the signal at either 5 Hz (DA models) or 25 Hz (DZ models).

Совместимая подставка

Совместимые экраны & интерфейсы ПК

  • T-Rad-Analog T-Rad-Analog

    Analog (BNC) power module, to interface THZ-B heads with oscilloscopes and lock-in amplifiers.

Возможности измерения

  • Максимальная средняя мощность

    25 μW

  • Эквивалентная мощность шума

    1 nW

  • Спектральный диапазон

    10 - 3000 μm

  • Частота

    0,1 - 30 THz

  • Типичное время нарастания

    0.2 s

  • Типичная чувствительность по мощности

    70 kV/W

  • Частота модуляции

    5 Hz

  • Минимальная частота повторения

    1000 Hz

Пределы прочности

  • Максимальная средняя плотность мощности

    0,01 W/cm²

Физические характеристики

  • Диаметр диафрагмы

    5 mm

  • Абсорбер

    BL

  • Размеры

    66.0Ø x 46.5D mm

  • Вес

    0,23 kg
Распечатать характеристики

CA$3,074.00*

CONTACT SALES

THZ-B-DA DETECTOR AND OSCILLOSCOPE

Here is a basic analog set up that would be useful if the optical power of the source was about 5 µW or greater. The output of the THZ5B-BL-DA detector would be approximately 600 mV @ 5 Hz chopping frequency, giving plenty of signal for an oscilloscope. Simply read the voltage output and divide by the Rv factor (V/W) of the detector to measure the intensity of the source in Watts. Also consider applying a wavelength correction factor under certain circumstances.

THZ-B-DA DETECTOR AND LOCK-IN AMPLIFIER

This is another analog set-up option that we recommend if you have to measure very low power levels (i.e. less than 5 ?W) where the signal may be buried in the broadband noise. The voltage output of the analog THZ-B-DA detector, powered by our T-RAD-ANALOG, is routed to the Lock-In Amplifier input, and the Sync Output of our SDC-500 Chopper is connected to the reference input. The Lock-In Amplifier will lock on the chopping frequency and you can dial in a long integrating time and measure a very low RMS voltage. The voltage divided by our Voltage Responsivity (V/W) equals the power of the source.

Связанные видео

All videos

Совместимые продукты, которые могут вам понадобиться

*Does not include shipping fees, import fees or local representation. Request quote for full details and local sales contact.

Your item has been added to your cart!

You might need these specific products to be able to use the placeholder only.

Compatible products

No compatible product

Проверить, работает ли этот продукт с вашим лазером

Тип измерения:

1

Размер луча

2

Тип лазера

3

Профиль луча

COPYRIGHT ©2024 Gentec-eo Spektrum média